Products Overview

Panel Beater 1050 US Spot Welder/Dent Puller #1 Product Seller!

The Panel Beater 1050 US is a Resistance Spot Welder/Dent Puller. The 1050 US produces professional 6mm factory type welds and is equipped with air cooled cables. The unit spot-welds supports and panels and removes dents and creases fast and easy.  The unit is high amperage battery operated and there are no heavy powers sources required.  Welds penetrate galvanizing, sealers and coatings.   The 1050 US has been approved by the makers of Fusor Repair Adhesives for weld bonding.

The Panel Beater 1000-DX Dent Puller

The Panel Beater Model 1000 Deluxe is a dent-pulling machine. The machine is powerful, portable and affordable for all shops large or small. The Panel Beater is high amperage battery powered. The machine removes dents and creases fast and easy. Simply stick the electrode to the dent by pushing the switch, pull out the dent and twist the electrode free. The machine includes a shrink tool for bulges and tightening metal.

Wave Wire Package 

The Wave Wire Package consists of the following:

• 4 Finger Claw

• 10 Finger Claw

• 1/2 lb. Wave Wire & Tool

This accessory is for all models of the Panel Beater machines.  See photo on the Panel Beater Dent Puller brochure page.

ARC Slide Hammer

The ARC Slide Hammer attaches easily to the dent pulling control handle on all the Panel Beater machines.  See photo on the Panel Beater Mig Welder brochure page.

The Panel Beater 1022 Mig Welder  

The Panel Beater Model 1022 Mig Welder is a complete turn-key Mig Welding System.  Just add safety gear and your ready to weld.  With the variable speed/heat control dial located in the welder itself, and controlled with your thumb, the ARC welder can be fine tuned while welding to produce the finest welds possible.  It is capable of producing welds which conform to ANSI/AWS Standards.

The 1022 Mig Welder is also available with powerful 12/24 Jump Start capabilities.

The Panel Beater 1025W Mig Welder/Dent Puller  

The Panel Beater Model 1025W Mig Welder/Dent Puller is a high amperage battery powered mig welder/dent puller. The unit has an output amperage equal to 220 volt models.  Use anywhere in the shop or yard, the machine is totally portable.  Lead acid batteries can supply approximately double the current of a 120 volt plug in welder or about 200 amps at 24V.  The 1025W yields up to 6 hours of welding before recharging.  It pulls hundreds of times on a single charge.  The machine removes dents and creases fast and easy and has excellent shrinking abilities.

1250 Hybrid System Resistance Spot Welder/Dent Puller
The 1250 Hybrid System is a Resistance Spot Welder/Dent Puller. The welder can produce 10,000 electrode amps with 10 feet of cable reach. This unit also has a high duty cycle, but unlike inverter welders, this welder only requires 110 volt 20 amp power source. Along with up to 1000 lbs of electrode tip pressure, the weld nuggets measure 8.7mm on 3 + 3mm structural steel. This 4 cable system has a smart digital microprocessor which monitors the welder’s performance at all times

Panel Beater 1015 DBL Single Side Spot Welder/Dent Puller 
The Panel Beater 1015 DBL is a Single Side Spot Welder/Dent Puller. It has a 4000 D.C. Amp capability. We will provide more details as they come available.

Power Booster 1500D

The ARC Power Booster instantaneously starts Trucks, Cars, Tractors, and Heavy Equipment.  The machines are powerful, portable and profitable by eliminating delays that cost time and money.  The Power Booster comes complete with a self-regulating charger and will not overcharge.  There are many models available to fit any need required.  The machine is built to last with rugged steel construction and heavy duty cables and clamps.

All Equipment has a full 1-year warranty and a Pro-rated battery warranty.

All machines are available for 100/120/200/220/230/240 volt power sources.

Financing is available O.A.C within the USA.